Casting Reel Basic Maintenance Disassembly Steps And Precautions

0 comments

Most Lure players have never dismantled the wheels. Many times they have played in seawater and just washed them with water. Let me give you a brief introduction to the steps of disassembly:

Casting Reel Basic Maintenance Disassembly Steps And Precautions

Let me introduce you to this 17-spider sv wheel. (Most water drop wheels are similar, and the internal structure is basically the same)

First prepare the tools, 10mm socket (no wrench is available, it is better to use a socket wrench, as the adjustable wrench can slip, and damage the nut), the bearing ejector rod, a small screwdriver, a brush, grease and lubricating oil, this will not be displayed to avoid suspicion of advertising.

Casting Reel Basic Maintenance Disassembly Steps And Precautions
Casting Reel Basic Maintenance Disassembly Steps And Precautions

First, remove the rocker arm screw, remove the nut fixing piece, unscrew the nut, and remove the rocker's arm. This is very simple and will not be explained too much.

Casting Reel Basic Maintenance Disassembly Steps And Precautions

Take down the cooperation spring, and unscrew the cooperation nut, washer, and cooperation clicker by hand. Then unscrew the three screws of the main cover, the longest of the three screws is the one on the side of the twist stick, and the other two are the same. The following is the order of parts removed

Casting Reel Basic Maintenance Disassembly Steps And Precautions
Casting Reel Basic Maintenance Disassembly Steps And Precautions

Then pick up the main cover and unscrew the trimmer cap. In turn, use a screwdriver to pry open the fine-tuning bearing fixing card, and in turn, use a screwdriver to poke out the bearing. Lubricate.

Casting Reel Basic Maintenance Disassembly Steps And Precautions
Casting Reel Basic Maintenance Disassembly Steps And Precautions
Casting Reel Basic Maintenance Disassembly Steps And Precautions

The disassembled interior is like this. For beginners who are just learning to dismantle the wheels, I suggest dismantling them here. The large and small gears and the main shaft do not need to be disassembled for the wheels that have not been used for a long time. Put some grease on the large and small gears and the moving parts. Put some grease on it. Then follow the removal steps to put it back together. See the order of parts above.

Casting Reel Basic Maintenance Disassembly Steps And Precautions

It must be noted that the one-way bearing sleeve is installed first, and then the main cover is closed.

Casting Reel Basic Maintenance Disassembly Steps And Precautions

The protruding part of the single-bearing sleeve is aligned with the groove of the cover plate, as shown in the picture above, and it will be fine. Close the main cover and screw on the screws

Casting Reel Basic Maintenance Disassembly Steps And Precautions
Casting Reel Basic Maintenance Disassembly Steps And Precautions

Among the three screws, the longest one is the circled one in the picture above, and the other two are the same.

Casting Reel Basic Maintenance Disassembly Steps And Precautions

Then reinstall the cooperation clicker, gasket, cooperation nut, spring, five-star cooperation, rocker arm, and rocker arm fixing nut and mount the fixing piece at a time.

Casting Reel Basic Maintenance Disassembly Steps And Precautions

The side cover part is relatively simple, unscrew the side cover, make a hook to hook out the side cover bearing, put some lubricating oil on it, and put it back.

The following briefly explains the left and right of these components.

The bearing of the side cover and the fine-tuning bearing is mainly responsible for the rotation of the spool (of course, the bearing of the short-axis cup is on the spool). The smoothness of casting is the role of these two bearings. People who often play in seawater My friend suggested paying attention to these two bearings. Once these two bearings enter seawater, they will rust after a few days, and they will rust to death after a long time. Make sure that these two bearings are not short of oil, and that the wheels are still so good after a long time of throwing.

Leave a comment

All blog comments are checked prior to publishing
You have successfully subscribed!
This email has been registered